girl pin size

[lyn]

hi guys. i was wondering if a could use a 1 cc 25 5/8" pin for primo injects into my leg ( waiting for the stealth primo) i plan on doing 1cc per week to start. i want to get my pins at a vet supply place, and they only have a few sizes to choose from. thanks lyn

[rAJJIN]

yes Ive used those plenty a times... A Bit hard to push but they will work.

[lyn]

great,that is what i wanted to hear! will 25 g work with most injects? thanks lyn.

[jstforme]

great,that is what i wanted to hear! will 25 g work with most injects? thanks lyn.

as in injection spots or injectables

[anaholic]

i would just get some 23ga, you have to push the plunger to hard with 25ga, and if you dont have the twist lock syringe you can blow the needle off and shoot the gear allover the place

[rAJJIN]

great,that is what i wanted to hear! will 25 g work with most injects? thanks lyn.


Yes itll work with most all injectables.... Thing as as said a few times already itll be harder to push so yea make sure tip is on tight and Just take your time
pushing it thru.../. All said and done by the time you push so hard and wobble it around... in the end the 23g would probably be less painfull even though they are a bit bigger.

they will work though, Ive used them 100`s of times for shoulder and Arm injections.

[lyn]

this will be the first time i will be injecting, so im just looking for the easiest way. i guess im just being a lil chicken

[tl49burne]

Lyn, I switched from 22's to 23's and noticed almost no pain all with the23's. Like the other guys said it'll take more time and pressure with 25's. I would def recommend 23's. Also, you can order thru gpz online with no questions asked and good service. Good luck. :cool:

[Kaiser]

One thing to keep in mind Lyn is that if the needle is small, and you have to push harder, there are more chances the pin is going to move around inside of you due to instability which will give you black and blue marks and has more of a chance of breaking off inside you so be careful. Try 23's out first and see how that works out. You can also get pinz from the sponsor at the top of the board with excellent prices & quick shipping so you are not limited in available sizes.

[lyn]

thanks guys, i will suck it up and go with the 23's

[Bakes]

Heat your gear before you shoot, it will help make the oil less viscous allowing for a much smoother inject through a 25G pin. It will also allow the oil to disperse through your muscle much more efficiently lowering the chance of a sterile oil abcess amoung other things.

[lyn]

hey bakes how do i heat it ? i want to get stealth, and store in pins.

[rAJJIN]

Bakes actually has a good idea there.
If its stealth what youll need to do is Take them out of the packets and Put into a sealed STERILE vial (which you can get here- www.kaotikchemistry.com)

After you have it in the sterile vial Just warm the sterile vial a bit.
Of course you dont want to heat it TO MUCH.. Just enough to make it thinner
but not enough to burn a hole in yo ass :eek: :D

Id just use hot tapwater...set the bottom ofd the vial in it a few minutes untill you can tell its warmed up, from there you have to use common sence to not get it to Hot, but warm enough.

Its no something you Have to do but it is a good tip that could help you out.

I guess you could also just run some hot water over the pin but be carefull
not to get it towards the tip where water could get in there.

[Bakes]

I guess you could also just run some hot water over the pin but be carefull
not to get it towards the tip where water could get in there.

Using the sterile vial to store and heat up your gear is a much better way for many reasons but if you intend to just store the Stealth inside syringes than the only other option is to use running tap water (hot obviously.lol) to heat you're gear in the rigs. Leave on the drawing pin and don't switch it out until you are ready to shoot. Hold the syringe under the hot water flow horizontal to the floor, ie. with the pin facing to the side, NOT up and down. Allow the water to flow around the barrell of the syringe, not onto the tip or inside the back, just flow over the barrell and drop off into the sink. This is the tricky part as you will have to make sure to keep the water away from the tip so there is no chance that you will contaminate your shot with unsterile water.
After you heat you're gear in this manner I blow off the excess water and then whipe everything down with an alcohol soaked pad before I switch tips.
I have done this method many times in the past and have had no problem what so ever. I also found that with more painful gear, heating it before I shot it greatly reduced the pain the next day, ect. as the oil dispersed so much more effortlessly resulting in no lumps or pain. :)

[Testament]

It's always funny how the female's posts get so many replies so quickly. :)